[PlanetCCRMA] No sound configuring RHC3

John S. Dey jsdey@optonline.net
Thu Mar 17 13:24:01 2005


Brad,

I ran aumix and increased vol and spkr to mid-range and verified that 
the values were saved.  Still no sound from aplay.

On Mar 17, 2005, at 4:03 PM, Bradley S. Campbell wrote:

> John,
>
> Have you tried running aumix as root?  You may notice that all the 
> levels are turned down.  I have FC3 and getting sound to work on it 
> doesn't seem to be a trivial undertaking.  Best of luck!
>
> Brad
>
>
> John S. Dey wrote:
>
>> Hi,
>>
>> I just installed RHC3 and updated software and sound programs.  aplay 
>> does not not result in any sound.  I did run alsamixer and turned 
>> volume up.
>>
>> The follow data might provide you with an idea of what I have missed. 
>>  Any comments or suggestions would be greatly appreciated.  Thanks
>>
>> John
>>
>> [root@jsdey etc]# uname -r
>> 2.6.10-2.1.ll.rhfc3.ccrma
>> Sound plays using the following test:
>> Application->System Settings->Soundcard Detection
>>
>>
>> -- modprobe.conf
>>
>> alias eth0 8139too
>> alias snd-card-0 snd-emu10k1
>> options snd-card-0 index=0
>> install snd-emu10k1 /sbin/modprobe --ignore-install snd-emu10k1 && 
>> /usr/sbin/alsactl restore >/dev/null 2>&1 || :
>> remove snd-emu10k1 { /usr/sbin/alsactl store >/dev/null 2>&1 || : ; 
>> }; /sbin/modprobe -r --ignore-remove snd-emu10k1
>> alias usb-controller ehci-hcd
>> alias usb-controller1 uhci-hcd
>> # --- BEGIN: Generated by ALSACONF, do not edit. ---
>> # --- ALSACONF verion 1.0.8 ---
>> alias snd-card-0 snd-emu10k1
>> alias sound-slot-0 snd-emu10k1
>> # --- END: Generated by ALSACONF, do not edit. ---
>>
>> [root@jsdey robo6]# /etc/rc.d/init.d/alsasound restart
>> Shutting down sound driver                                 [  OK  ]
>> Starting sound driver snd-emu10k1                          [  OK  ]
>> Starting sound driver snd-emu10k1                          [  OK  ]
>> Starting sequencer                                         [  OK  ]
>> Starting sequencer driver snd-emu10k1-synth                [  OK  ]
>> Starting sequencer driver snd-seq-midi                     [  OK  ]
>> Restoring sound driver settings /usr/sbin/alsactl: load_state:1267: 
>> No soundcards found...
>>                                                            [FAILED]
>> Whoops!!!!
>>
>> [robo6@jsdey ~]$ aplay -device="plughw" 01-Overture.wav
>> Playing WAVE '01-Overture.wav' : Signed 16 bit Little Endian, Rate 
>> 44100 Hz, Stereo
>> Aborted by signal Interrupt...
>>
>> _______________________________________________
>> PlanetCCRMA mailing list
>> PlanetCCRMA@ccrma.stanford.edu
>> http://ccrma-mail.stanford.edu/mailman/listinfo/planetccrma
>
>
> _______________________________________________
> PlanetCCRMA mailing list
> PlanetCCRMA@ccrma.stanford.edu
> http://ccrma-mail.stanford.edu/mailman/listinfo/planetccrma
>