FC4 troubles (was [PlanetCCRMA] New user; FC3 or FC4?)

Matt Marian matt1@mattmarian.homelinux.com
Wed Nov 30 20:44:01 2005

Michael Gurevich wrote:

>I don't usually weigh in on these things, but for what its worth, I'm 
>still having problems with FC4 and planetCCRMA.
>The planetCCRMA smp kernels still don't boot for me, and unfortunately 
>I don't have time/patience/expertise to start recompiling the kernel. 
>The uni-processor ones boot, but crash after awhile. I'm back to using 
>RedHat's latest smp kernel.
>Not totally sure how to investigate the crashes with the CCRMA kernel. I 
>don't use the machine all the time, but if I leave it running for more 
>than an hour or so, its normally frozen with a blank screen when I come 
>back to it. I looked in /var/log/messages, and the only notable difference 
>between the RH and CCRMA kernels is that with the CCRMA kernel I get the 
>messages copied below periodically. When the machine freezes, there is 
>one crond job after these messages, and then nothing. But it doesn't 
>freeze everytime these messages appear.
>Nov 28 15:18:23 localhost kernel: irq 21: nobody cared (try booting with 
>the "irqpoll" option)
>Nov 28 15:18:23 localhost kernel:  [<c01471b4>] __report_bad_irq+0x24/0x90 
>Nov 28 15:18:23 localhost kernel:  [<c01472c2>] note_interrupt+0x72/0xd0 
>Nov 28 15:18:23 localhost kernel:  [<c0146ec4>] do_hardirq+0xe4/0x110 (20)
>Nov 28 15:18:23 localhost kernel:  [<c0146ef0>] do_irqd+0x0/0x90 (20)
>Nov 28 15:18:23 localhost kernel:  [<c0146f52>] do_irqd+0x62/0x90 (8)
>Nov 28 15:18:23 localhost kernel:  [<c0137078>] kthread+0x98/0xa0 (24)
>Nov 28 15:18:23 localhost kernel:  [<c0136fe0>] kthread+0x0/0xa0 (12)
>Nov 28 15:18:23 localhost kernel:  [<c01013b1>] 
>kernel_thread_helper+0x5/0x14 (12)
>Nov 28 15:18:23 localhost kernel: handlers:
>Nov 28 15:18:23 localhost kernel: [<c02b08d0>] (usb_hcd_irq+0x0/0x80)
>Nov 28 15:18:23 localhost kernel: turning off IO-APIC fast mode.
>On Wed, 30 Nov 2005, Fernando Lopez-Lezcano wrote:
>>On Tue, 2005-11-29 at 23:18 +0100, Paquita wrote:
>>>I'm new to audio under linux, and about to try Planet CCRMA. I read a bit,
>>>but currently it's not clear to me which Fedora Core version I should
>>>install : is Planet CCRMA already ready for FC4? Or am I better off
>>>staying with FC3 right now?
>>This is getting harder and harder to answer :-) FC3 is still the most
>>complete system in terms of software available, there are a few
>>ommissions still in FC4 - after the initial flurry of help I got to get
>>things compiled on gcc4 the enthusiasm died down and I have been too
>>busy to try again. Most probably by now those problems already have
>>The only major advantage I see in FC3 is the availability of cdrom
>>images which I have not recreated yet for FC4 (but FC4 has a full blown
>>"all included" install dvd - experimental, of course). If you don't need
>>them you could go with FC4. For the current status of the FC4 packages
>>as compared to FC3 see:
>>  http://ccrma.stanford.edu/planetccrma/software/fc4buildstatus.html
>>-- Fernando
>>>I'd rather have a stable system, and I doubt I will need anything really
>>>cutting edge. My goal is to do multitrack recording using an M-Audio Duo
>>>USB interface.
>>PlanetCCRMA mailing list
I got the same - Nobody cared error
check your Ide/raid controller setups in the bios.
If you don't have it in compatible mode and the hardrives and CDROM/DVD  
use the same interupt then you will have problems
for example - - set in enhanced mode if you are using sata controllers 
in conjunction with an IDE controller they might not be able to both use 
the primary .
Some boards allow  dual use and all  to be used  and some are set as  
slow down and think carefully how you have all of your drives connected.
some boards have an individual IDE controller (main- Primary) that is 
also linked to an SATA Primary - or infact another IDE set as RAID/IDE 
and it is also a Primary and you are putting devices on a channel that 
causes a conflict- thus the " nobody cared" scenario in your errors.
I bet this is the problem
1st - change the IDE/SATA settings to compatible
Choose either P/ata only ( S/ata only ) or Both P/ata +S/ata
-REBOOT -go back into the bios.
then look at your available IDE/SATA devices.
make sure if you are using P/ata you are setting Primary devices on the 
correct controller and use only Primary  ones,   watch your master/slave 
positions  . .  
- go re-read that, it looks convoluted but trust me, this is what is 
happening.   you WILL get it to work if you map out what is a Primary 
Parallel IDE controller and and which is a  Primary Sata controller  
and  use the master on one and the secondary on the other.
umm I might not have said that exactly correct , but check the bios 
setting for your IDE controller and think carefully about what Drive , 
what controller, and what position.